Install heavy gauge stainless steel screen over attic fan housing to prevent animal entry. Replace fan thermostat. Install Leaf Solutions on front and rear gutters. These keep the gutters from clogging and prevent animal entry. Install aluminum coil stock over rake boards and corners to repair animal damage at each …

Prior to any insulation being installed an electrician will need to check and repair any chewed wires. Remove all of the batted/blown in insulation and feces. Use Sterifab to disinfect. Install new baffles at the soffit point and around the entry point. Blow in all new cellulose insulation to …

Remove all blown/batted insulation. Remove animal feces and use Steirfab to disinfect. Air seal gaps and conduit lines for energy efficiency. Install can light covers over the recess lights. Seal around the kitchen exhaust pipe. Install new baffles at the soffit lines and around dedicated storage space. Install attic …

Using spray foam insulation seal up all penetrations from plumbing, electrical lines and fixtures, and hvac ducts. Then, redistribute the existing insulation as evenly as possible. Install reflective radiant barrier on rafters in the attic.

Install heavy gauge stainless steel attic roof fan guard. This is a very common entry point for squirrels, flying squirrels, and raccoons — they can push the small screen attached to the fan housing aside, or chew through it, or pull it off in the case of a raccoon. Caulk to …

Remove current R-30 batt insulation. Sanitize as able Air seal accessible top plates, gaps and ceiling penetrations 1″ or less with sprayfoam. Install baffles as able Install new cellulose blown in insulation @ recommended r-49 level. Create new scuttle access door.

Remove current blown in and batt insulation in primary attic space and above vaulted ceiling.Sanitize area as able. Air seal accessible top plates, gaps and ceiling penetrations 1″ or less with sprayfoam Install baffles Install batt insulation in area above vaulted ceiling at recommended r-38 level (Approx 240sqft) Install cellulose …

Remove section of the valley indicated by the technician on the front right side. Install new section of plywood, ice/water shield, and new three tab shingles. Replace section of the rake board and re install the existing metal. If metal is damaged in the process it will be replaced …

Using aluminum coil stock in a matching color seal up the soffit and rake boards On the front left section of the roof framing.

Open up portions of ceiling in dinning room to access 3 feet inch flex. Remove old flex and install new line from bath fan to outside vent. Clean up any debris and sanitize if found in ceiling due to possible line breach. Reinstall drywall with 1 coat of spakle, no paint.

Blow over existing insulation in the main attic space to reach levels of 14 inches (R49). New cellulose insulation will be used. New baffles will be added to the soffit lines to keep proper ventilation. Foam board insulation will be installed on the entry door and weather stripping at the entry …

Remove old metal ridge vents on the second story of the home. Install all new shingled ridge vents to match existing color as best as possible. Replace section of shingles and plywood that were damaged indicated by the technician. New shingles will not fully match due to age of the …

Install foam board insulation over the entry point. Install new baffles at the soffit lines. Insulate the skylights with R13 batted fiberglass insulation. Skylight gaps will be air sealed with spray foam prior to installing the new fiberglass batts. Blow in new cellulose insulation to reach 14 inches (R49).

Mold Lead and Insulation -on the second floor of home visible mold from water leaks on all 4 sides of home peeling paint test positive for lead on walls going down the stairway to back door remove dry wall to get to areas where is bad suck out old contaminated insulation …

Remove batted and blown insulation from entire attic space. Apply blown cellulose to bring insulation back to R49. Apply closed cell foam to vertical area of vaulted ceiling near center of attic. Seal all penetration points. Demo batted on skylight on right side rear. Apply 2 inches of closed cell foam …